24 May 2010

Plug and play: Directives and standards

Does your 'previously approved' power supply meet UK plug pin requirements?

Growing numbers of industrial and consumer products rely upon a 'previously approved' power supply. These 'approved' power supplies can provide significant benefits, allowing a manufacturer to reduce design, manufacture and approval costs.

But test houses are finding some preapproved power supplies do not meet the correct mains plug tests. In such instances, they must undergo further evaluation and failure to meet the requirements will result in the product being removed from the UK market.

UK regulations require that all domestic electrical goods are fitted with an appropriate mains plug, not only making sure that mains plugs make good connections with sockets, but also that plugs are suitably fused. Since the UK ring main system can deliver 32A (1500A instantaneously), the mains fuse is critical to protect the mains cord. Despite the safety implications, Trading Standards have found instances where traders have relied upon the CE mark and made no attempt to ensure that such plugs were safe.

Failure to comply with the relevant requirements can cause lengthy delays to a product's approval. For example, it can take two weeks to provide a test report for the power supply itself. If a product is subjected to a verification procedure and is found to be non compliant, it can then take a further two or three weeks to test the power supply plug to the appropriate standard – in this case BS 1363-1. Further misery could be experienced if the non compliance is serious enough to require a redesign or change in power supply.

Changing a power supply at such a late stage could be catastrophic for a product's market release plans and it has been known for projects to be cancelled at this stage, even after considerable financial outlay.

A number of 'plug in' chargers have been removed from the UK market after serious non compliances were found. One example is a mobile phone charger whose power supply was CE marked and had a EN 60950-1 test report. However, on verification, it was found that there were not only electrical issues with the chargers, but also dimensional issues with the plug pins – the live pins were too close to the periphery of the plug, which could lead to an electric shock when inserting into the mains outlet. Furthermore, the live and neutral pins were not robust enough. This unit is now prohibited from being placed on the UK market.

It is advisable to check the IEC or EN test report for specific coverage of the necessary national deviations. It's also a good idea to check that the original test lab's accreditation is up to date – critical in confirming the product is fit for the UK market. If in doubt, seek advice from an accredited test laboratory, which can then review the test report and check all relevant tests are complete and correct.

Seeking expert advice is particularly important if testing has been performed under the IECEE CB scheme, a mutually recognised system for cross territory safety testing. This requires testing to a core IEC standard, which is enhanced by national deviations. CB certificates, stored on the IECEE website, follow a standard format, stating national deviations carried out by the test laboratory. This verification procedure determines whether the power supply is suitably approved for use in the specific country of choice.

Despite the UK's requirement for testing to BS 1363-1, the specific national deviation for the UK under EN 60950-1 (clause 4.3.6) has been marked as 'not applicable' by various Far East test laboratories. Checking this clause within test reports is essential to ensure the product has undergone the required testing.

It is critical that a previously approved power supply has its safety compliance verified. This not only ensures user safety, but also minimises the risk of additional costs and delays affecting the launch schedule and profitability.

Author profile:
Chris Adkin is principal engineer with TRaC

Chris Adkin

Supporting Information



TRAC Precision Machining Ltd

This material is protected by Findlay Media copyright
See Terms and Conditions.
One-off usage is permitted but bulk copying is not.
For multiple copies contact the sales team.

Do you have any comments about this article?

Add your comments


Your comments/feedback may be edited prior to publishing. Not all entries will be published.
Please view our Terms and Conditions before leaving a comment.

Related Articles

'Power supply in a package’

Intersil has introducted the ISL8216M, an 80V, 4A non isolated DC/DC step down ...

Brick modules updated

The PFE-SA series of AC/DC full brick power modules from TDK Lambda is said to ...

€55m power electronics project

Described as one of the most important European energy efficiency research ...

Power electronics challenges

There isn't a sector of the electronics industry that operates without the use ...

A/D converters get it right

Successive approximation A/D converters, with resolutions of up to 18bit and ...

DC transmission on a comeback

The pressure throughout the energy supply chain to deliver electrical power ...

Power electronics in EVs

This whitepaper presents a review of power electronics systems in electric ...

Power management ics

This whjitepaper presents various application scenarios where high voltage ...

Power saving techniques

Wireless telecommunications has given rise to a host of new portable ...

6W DC/DC converters

XP Power has announced the ITX series of 6W DC/DC converters. Available in an ...

Low voltage power supplies

TDK has added 12 and 15V models to its ZWS300BAF series of single output power ...

1W DC/DC converters

Murata has announced the NCS1 family of single output, 1W DC/DC converters.

PCIM Europe 2014 Conference

20th – 22nd May 2014, Nuremburg, Germany

Power management forum

28th October 2014, Williams F1 Centre, Oxford


In this video product marketing engineer, Rich Nowakowski, discusses a family ...

TI power design tools

Discover and get to market faster with TI Power Design Tools; easy-to-use ...

3E EPM Hands on Digital Power

Introduced by Ericsson in 2008, 3E* digital power products and solutions became ...

Packing a powerful punch

Power is back when it comes to industrial system performance and efficiency. ...

Powering ahead

Too often in the past, electronics industry initiatives have been announced ...

Regulated power?

Power supply specialists will no doubt be raising an eyebrow at a report which ...

Ashley Evans, Electronics KTN

As the Electronics KTN evolves, it will face a new set of challenges. Graham ...

Patrick Le Fèvre, Ericsson

Patrick Le Fèvre, marketing director, Ericsson Power Modules, talks with Chris ...

Andy Gales, vp, Vicor

Andy Gales, vice president, international sales, Vicor, talks with Chris Shaw