comment on this article

Imec demonstrates scalable III-V and III-N devices on Si

imec has presented the first functional GaAs-based heterojunction bipolar transistor (HBT) devices on 300mm Si, and CMOS-compatible GaN-based devices on 200mm Si for mm-wave applications.

The results demonstrate the potential of both III-V-on-Si and GaN-on-Si as CMOS-compatible technologies for enabling RF front-end modules for beyond 5G applications and were presented at last year’s IEDM conference (Dec 2019, San Francisco).

In wireless communication there is a push towards higher operating frequencies, moving from the congested sub-6GHz bands towards mm-wave bands (and beyond). The introduction of these mm-wave bands will have a significant impact on the overall 5G network infrastructure and on mobile devices.

For mobile services and Fixed Wireless Access (FWA), this is likely to translate into increasingly complex front-end modules that send the signal to and from the antenna. To be able to operate at mm-wave frequencies, the RF front-end modules will have to combine high speed (enabling data rates of 10Gbps and beyond) with mcuh high output power.

In addition, their implementation in mobile handsets puts high demands on their form factor and power efficiency.

Beyond 5G, these requirements can no longer be achieved, even with today’s most advanced RF front-end modules that typically rely on a variety of different technologies amongst others GaAs-based HBTs for the power amplifiers – grown on small and expensive GaAs substrates.

"To enable the next-generation RF front-end modules beyond 5G, imec is looking at CMOS-compatible III-V-on-Si technology”, said Nadine Collaert, program director at imec. “Imec is looking into co-integration of front-end components (such as power amplifiers and switches) with other CMOS-based circuits (such as control circuitry or transceiver technology), to reduce cost and form factor, and enabling new hybrid circuit topologies to address performance and efficiency.

"Imec is exploring two different routes: Firstly, Indium Phosphide (InP)on Si, targeting mm-wave and frequencies above 100GHz (future 6G applications) and, secondly, GaN-based devices on Si, targeting (in a first phase) the lower mm-wave bands and addressing applications in need of high power densities.

"For both routes, we have now obtained first functional devices with promising performance characteristics, and we identified ways to further enhance their operating frequencies.”

Functional GaAs/InGaP HBT devices grown on 300mm Si have been demonstrated as a first step towards the enablement of InP-based devices. A defect-free device stack with below 3x106cm-2 threading dislocation density was obtained by using imec’s III-V nano-ridge

engineering (NRE) process. According to imec, the devices perform considerably better than reference devices, with GaAs fabricated on Si substrates with strain relaxed buffer (SRB) layers.
In a next step, higher-mobility InP-based devices (HBT and HEMT) will be explored.
Moreover, CMOS-compatible GaN/AlGaN-based devices on 200mm Si have been fabricated comparing three different device architectures – HEMTs, MOSFETs and MISHEMTs. It has been shown that MISHEMT devices outperform the other device types in terms of device scalability and noise performance for high-frequency operation.
Peak cut-off frequencies of fT/fmax around 50/40 were obtained for 300nm gate lengths, which is in line with reported GaN-on-SiC devices. Besides further gate length scaling, first results with AlInN as a barrier material show the potential to further improve the performance, and hence, increase the operating frequency of the device to the required mm-wave bands.
Above: Description of the NRE approach for hybrid III-V/CMOS integration on 300mm Si: (a) nano-trench formation; defects are trapped in the narrow trench region; (b) HBT stack growth using NRE and (c) different layout options for HBT device integration.

Author
Neil Tyler

Comment on this article


Websites

http://www.imec.be

Companies

IMEC

This material is protected by MA Business copyright See Terms and Conditions. One-off usage is permitted but bulk copying is not. For multiple copies contact the sales team.

What you think about this article:


Add your comments

Name
 
Email
 
Comments
 

Your comments/feedback may be edited prior to publishing. Not all entries will be published.
Please view our Terms and Conditions before leaving a comment.

Related Articles